Sign Repair
8
min read

How to Fix a Broken Neon Sign (and When to Call a Pro)

Illuminated blue and pink neon letters, the kind of glass tubing Rick Signs repairs and re-bends in Chicago
Written by
Rick Signs Team
Published on
November 3, 2026

How to fix a neon sign safely — the five checks any owner can do, how to read the symptoms, and where the job turns into high-voltage work for a neon pro.

You flip on the lights before opening and the neon in the front window just sits there. Or half the word is lit and the other half is dark. Or one letter is glowing a weird washed-out pink. You've got customers in an hour and you're wondering if this is a five-minute fix or a new sign.

Most of the time it's neither. After 35 years of fixing Chicago neon, we can tell you that a surprising number of "broken" signs are a tripped outlet or a timer that got knocked out of sync. The rest need someone with the right equipment and a glass bench.

Here's how to tell the difference without getting hurt.

Can you fix a neon sign yourself?

You can safely check the power side of a neon sign, but anything past the plug and switch is high-voltage work for a pro.

A neon transformer takes 120 volts in and steps it up to thousands of volts on the output side, typically somewhere between 2,000 and 15,000 volts depending on the sign. That voltage runs through the GTO wire and the electrodes at each end of every tube. It can arc through cracked insulation and it can seriously injure you.

So the rule is simple:

  • Owner territory: power, switches, breakers, GFCI outlets, timers, a visual look from a safe distance
  • Pro territory: opening the transformer box, touching tubes or electrodes, GTO wire, anything with the sign powered on

What should I check first when my neon sign won't light?

Start with power, because most "dead" neon signs are a power problem, not a neon problem. Work through these in order:

  1. Is it plugged in and switched on? Window signs get bumped by cleaning crews and displays. Check that the plug is fully seated and any inline switch is on.
  2. Check the GFCI outlet. If the sign plugs into a GFCI receptacle, press reset. If it trips again right away, stop there. Repeated tripping usually means moisture or a fault in the sign, and that's a call to us.
  3. Check the breaker. Look for a tripped breaker on the sign circuit. Reset it once. If it trips again, leave it off.
  4. Check the timer. A timer that lost power or got bumped can keep the sign off during business hours. Make sure the time of day is correct and the on/off settings make sense.
  5. Look, don't touch. With the sign unplugged or the circuit off, look for cracked or broken glass, a tube that's come loose from its supports, scorched or melted wire, or a transformer box leaking dark tar.

If all of that checks out and the sign is still dark, you've done your part. Our full sign diagnostic guide walks through the same process for every sign type, not just neon.

How do I tell a broken neon tube from a bad transformer?

The pattern of what's lit and what's dark usually points to the cause before anyone opens the sign.

Neon tubes on one transformer are wired in series, like old Christmas lights. If one tube on that circuit cracks or loses its gas, the whole circuit can go dark or start flickering, not just the broken piece. Bigger signs often run several transformers, so you'll see one section out while the rest stays lit.

SymptomLikely causeOwner check or pro job?
Whole sign darkNo power, tripped GFCI or breaker, timer, or a failed transformerCheck power first; transformer is a pro job
One section dark, rest litFailed transformer on that circuit, a broken tube, or a wiring faultPro job
Tube glows pale pink, white or purple instead of its colorAir has leaked in; the tube has lost its gas fillPro job (tube must be re-processed)
Flickering or sputtering at the tube endsWorn electrode, loose connection, or a weak transformerPro job
Sign is dim overallAging transformer or tubes near end of lifePro job
Buzzing, hot smell, or tar on the boxTransformer overheating or failingTurn it off and call
Visible crack or broken glassPhysical damageTurn it off and call

A tube that changes color is a giveaway. Neon gas glows a distinct red-orange, and blues and other colors come from argon and mercury inside coated glass. When a hairline crack lets air in, the color goes wrong, then the tube stops lighting. If the sign flickers rather than going fully dark, our guide to flickering signs covers the usual suspects.

Can you glue or tape a broken neon tube?

No — a cracked neon tube has lost its vacuum, and no glue, tape or epoxy will bring it back.

A neon tube works because it's sealed and filled with a small amount of gas at low pressure. Once air gets in, the tube won't light properly, even if the glass looks whole again. Any patch that covers the crack still leaves contaminated gas inside.

The real fix happens on a neon bench:

  • Re-bend: a neon bender heats new glass and shapes it to match the original pattern, or splices in a new section
  • Process: the tube is heated under vacuum to burn out impurities (called bombarding)
  • Re-fill: it's filled with the right gas for the color and sealed
  • Burn in: the tube runs on the bench before it goes back in the sign

That's skilled glass work. It's why "neon repair" from a shop that only does LED often means "we'll sell you a new sign."

When is a failed transformer the problem?

When the whole sign or one full circuit is dark and power checks out, the transformer is the first suspect. Signs that point to it:

  • Totally dark with power confirmed at the outlet
  • Dim or weak across every tube on the circuit
  • Humming or buzzing louder than it used to
  • GFCI trips as soon as the sign turns on
  • Older units leaking tar from the case seams

Testing a transformer means measuring output with the right meter, under high voltage, so it's strictly pro work. Modern electronic neon power supplies also have built-in secondary ground-fault protection, which can shut the sign off when it senses a fault in old wiring or a wet tube. Sometimes the "bad transformer" is actually doing its job. We'll cover this in depth in Neon Sign Transformer Replacement: Signs It's Failing & What It Costs (coming soon).

When should I stop and call a neon pro?

Call as soon as the problem is past the plug, the switch, the breaker and the timer. Stop and call right away if you see:

  • Broken or cracked glass
  • A tube glowing the wrong color
  • Sparks, arcing, burning smell or smoke
  • A GFCI or breaker that trips again after reset
  • Exposed or scorched wire anywhere on the sign

Don't try to remove tubes or open the transformer box. Unplug it or turn off the circuit and leave the rest to someone with a meter and a bench. For what the actual repairs run, see our neon repair cost breakdown.

A word about our shop

Rick Signs and Repairs is a father-and-son shop on Bryn Mawr in Edgewater, fixing signs for Chicago businesses since 1989. Neon is one of the things we do best. We test transformers properly, trace GTO wiring, replace electrodes, and work with glass so broken tubes get re-bent and re-filled instead of thrown out.

If your sign is past the safe checks above, our neon sign repair service covers diagnosis, on-site fixes and bench work across Chicago and the suburbs.

Bottom line

Fixing a neon sign starts with the boring stuff: plug, switch, GFCI, breaker, timer. If those check out, the pattern of what's dark tells you a lot, but the repair itself is high-voltage and glass work. Broken tubes get re-made, not glued, and transformers get tested, not guessed at.

Do the safe checks, then let someone who actually fixes neon take it from there.


Related reading

Neon sign still dark after the safe checks? Call Tymothy at (773) 815-0006 or Rick at (847) 809-7900, or request a quote.